Welcome to download the newest Pass4itsure 1z1-060 VCE dumps: http://www.pass4itsure.com/1z1-060.html
Preparing for Microsoft exams of Cisco 100-101 is really a tough task to accomplish.Flydumps delivers the most comprehensive preparation material,covering each and every aspect of Cisco 100-101 exam curriculum and all the brain is the latest.You can pass Cisco 100-101 exam without any problem.
QUESTION 11
Which two commands will display the current IP address and basic Layer 1 and 2 status of an interface? (Choose two.)
A. router#show version
B. router#show ip interface
C. router#show protocols
D. router#show controllers
E. router#show running-config
Correct Answer: CD
QUESTION 12
An administrator is in the process of changing the configuration of a router. What command will allow the administrator to check the changes that have been made prior to saving the new configuration?
A. Router# show startup-config
B. Router# show current-config
C. Router# show running-config
D. Router# show memory
E. Router# show flash
F. Router# show processes
Correct Answer: C
QUESTION 13
On a live network, which commands will verify the operational status of router interfaces? (Choose two.)
A. Router# show interfaces
B. Router# show ip protocols
C. Router# debug interface
D. Router# show ip interface brief
E. Router# show start
Correct Answer: AD
QUESTION 14
Which router command will configure an interface with the IP address 10.10.80.1/19?
A. router(config-if)# ip address 10.10.80.1/19
B. router(config-if)# ip address 10.10.80.1 255.255.0.0
C. router(config-if)# ip address 10.10.80.1 255.255.255.0
D. router(config-if)# ip address 10.10.80.1 255.255.224.0
E. router(config-if)# ip address 10.10.80.1 255.255.240.0
F. router(config-if)# ip address 10.10.80.1 255.255.255.240
Correct Answer: D
QUESTION 15
Refer to the exhibit. If the resume command is entered after the sequence that is shown in the exhibit, which router prompt will be displayed?
A. Router1>
B. Router1#
C. Router2>
D. Router2#
Correct Answer: C
QUESTION 16
Refer to the exhibit. Which default gateway address should be assigned to HostA?
A. 192.168.1.1
B. 192.168.1.65
C. 192.168.1.66
D. 192.168.1.129
E. 10.1.1.1
F. 10.1.1.2
Correct Answer: B
IP Services QUESTION 1
What is the best practice when assigning IP addresses in a small office of six hosts?
A. Use a DHCP server that is located at the headquarters.
B. Use a DHCP server that is located at the branch office.
C. Assign the addresses by using the local CDP protocol.
D. Assign the addresses statically on each node.
Correct Answer: D QUESTION 2
A.
B.
C.
D.
Correct Answer:
QUESTION 3
A.
B.
C.
D.
Correct Answer:
QUESTION 4
A.
B.
C.
D.
Correct Answer: QUESTION 5
In the configuration of NAT, what does the keyword overload signify?
A. When bandwidth is insufficient, some hosts will not be allowed to access network translation.
B. The pool of IP addresses has been exhausted.
C. Multiple internal hosts will use one IP address to access external network resources.
D. If the number of available IP addresses is exceeded, excess traffic will use the specified address pool.
Correct Answer: C QUESTION 6
What happens when computers on a private network attempt to connect to the Internet through a Cisco router running PAT?
A. The router uses the same IP address but a different TCP source port number for each connection.
B. An IP address is assigned based on the priority of the computer requesting the connection.
C. The router selects an address from a pool of one-to-one address mappings held in the lookup table.
D. The router assigns a unique IP address from a pool of legally registered addresses for the duration of the connection.
Correct Answer: A QUESTION 7
When configuring NAT, the Internet interface is considered to be what?
A. local
B. inside
C. global
D. outside
Correct Answer: D QUESTION 8
The ip helper-address command does what?
A. assigns an IP address to a host
B. resolves an IP address from a DNS server
C. relays a DHCP request across networks
D. resolves an IP address overlapping issue Correct Answer: C
Network Device Security
QUESTION 1
Refer to the exhibit. The network administrator made the entries that are shown and then saved the configuration. From a console connection, what password or password sequence is required for the administrator to access privileged mode on Router1?
A. cisco
B. sanfran
C. sanjose
D. either cisco or sanfran
E. either cisco or sanjose
F. sanjose and sanfran
Correct Answer: B
QUESTION 2
A.
B.
C.
D.
Correct Answer:
QUESTION 3
The following commands are entered on the router:
Burbank(config)# enable secret fortress Burbank(config)# line con 0 Burbank(config-line)# login Burbank(config-line)# password n0way1n Burbank(config-line)# exit Burbank(config)# service password-encryption
What is the purpose of the last command entered?
A. to require the user to enter an encrypted password during the login process
B. to prevent the vty, console, and enable passwords from being displayed in plain text in the configuration files
C. to encrypt the enable secret password
D. to provide login encryption services between hosts attached to the router
Correct Answer: B
QUESTION 4
What is the effect of using the service password-encryption command?
A. Only the enable password will be encrypted.
B. Only the enable secret password will be encrypted.
C. Only passwords configured after the command has been entered will be encrypted.
D. It will encrypt the secret password and remove the enable secret password from the configuration.
E. It will encrypt all current and future passwords.
Correct Answer: E
QUESTION 5
An administrator has connected devices to a switch and, for security reasons, wants the dynamically learned MAC addresses from the address table added to the running configuration. What must be done to accomplish this?
A. Enable port security and use the keyword sticky.
B. Set the switchport mode to trunk and save the running configuration.
C. Use the switchport protected command to have the MAC addresses added to the configuration.
D. Use the no switchport port-security command to allow MAC addresses to be added to the configuration.
Correct Answer: A
QUESTION 6
A company has placed a networked PC in a lobby so guests can have access to the corporate directory. A security concern is that someone will disconnect the directory PC and re-connect their laptop computer and have access to the corporate network. For the port servicing the lobby, which three configuration steps should be performed on the switch to prevent this? (Choose three.)
A. Enable port security.
B. Create the port as a trunk port.
C. Create the port as an access port.
D. Create the port as a protected port.
E. Set the port security aging time to 0.
F. Statically assign the MAC address to the address table.
G. Configure the switch to discover new MAC addresses after a set time of inactivity.
Correct Answer: ACF QUESTION 7
Why would a network administrator configure port security on a switch?
A. to prevent unauthorized Telnet access to a switch port
B. to prevent unauthorized hosts from accessing the LAN
C. to limit the number of Layer 2 broadcasts on a particular switch port
D. block unauthorized access to the switch management interfaces
Correct Answer: B QUESTION 8
How can you ensure that only the MAC address of a server is allowed by switch port Fa0/1?
A. Configure port Fa0/1 to accept connections only from the static IP address of the server.
B. Configure the server MAC address as a static entry of port security.
C. Use a proprietary connector type on Fa0/1 that is incomputable with other host connectors.
D. Bind the IP address of the server to its MAC address on the switch to prevent other hosts from spoofing the server IP address.
Correct Answer: B Troubleshooting
QUESTION 1
Refer to the exhibit. An administrator cannot connect from R1 to R2. To troubleshoot this problem, the administrator has entered the command shown in the exhibit. Based on the output shown, what could be the problem?
A. The serial interface is configured for half duplex.
B. The serial interface does not have a cable attached.
C. The serial interface has the wrong type of cable attached.
D. The serial interface is configured for the wrong frame size.
E. The serial interface has a full buffer.
Correct Answer: C
QUESTION 2
Refer to the exhibit. A TFTP server has recently been installed in the Atlanta office. The network administrator is located in the NY office and has made a console connection to the NY router. After establishing the connection they are unable to backup the configuration file and IOS of the NY router to the TFTP server. What is the cause of this problem?
A. The NY router has an incorrect subnet mask.
B. The TFTP server has an incorrect IP address.
C. The TFTP server has an incorrect subnet mask.
D. The network administrator computer has an incorrect IP address.
Correct Answer: C QUESTION 3
If a host experiences intermittent issues that relate to congestion within a network while remaining connected, what could cause congestion on this LAN?
A. half-duplex operation
B. broadcast storms
C. network segmentation
D. multicasting
Correct Answer: B QUESTION 4
Refer to the exhibit. The junior network support staff provided the diagram as a recommended configuration for the first phase of a four-phase network expansion project. The entire network expansion will have over 1000 users on 14 network segments and has been allocated this IP address space.
192.168.1.1 through 192.168.5.255
192.168.100.1 through 192.168.100.255
What are three problems with this design? (Choose three.)
A. The AREA 1 IP address space is inadequate for the number of users.
B. The AREA 3 IP address space is inadequate for the number of users.
C. AREA 2 could use a mask of /25 to conserve IP address space.
D. The network address space that is provided requires a single network-wide mask.
E. The router-to-router connection is wasting address space.
F. The broadcast domain in AREA 1 is too large for IP to function.
Correct Answer: ACE
QUESTION 5
Refer to the exhibit. Host A can communicate with Host B but not with Hosts C or D. How can the network administrator solve this problem?
A. Configure Hosts C and D with IP addresses in the 192.168.2.0 network.
B. Install a router and configure a route to route between VLANs 2 and 3.
C. Install a second switch and put Hosts C and D on that switch while Hosts A and B remain on the original switch.
D. Enable the VLAN trunking protocol on the switch.
Correct Answer: B
QUESTION 6
Refer to the exhibit. A network administrator has configured a Catalyst 2950 switch for remote management by pasting into the console the configuration commands that are shown in the exhibit. However, a Telnet session cannot be successfully established from a remote host. What should be done to fix this problem?
A. Change the first line to interface fastethernet 0/1.
B. Change the first line to interface vlan 0/1.
C. Change the fifth line to ip default-gateway 192.168.17.241.
D. Change the fifth line to ip route 0.0.0.0 0.0.0.0 192.168.17.1.
E. Change the sixth line to line con 0.
Correct Answer: C
QUESTION 7
Refer to the exhibit. The network administrator is testing connectivity from the branch router to the newly installed application server. What is the most likely reason for the first ping having a success rate of only 60 percent?
A. The network is likely to be congested, with the result that packets are being intermittently dropped.
B. The branch router had to resolve the application server MAC address.
C. There is a short delay while NAT translates the server IP address.
D. A routing table lookup delayed forwarding on the first two ping packets.
E. The branch router LAN interface should be upgraded to FastEthernet.
Correct Answer: B QUESTION 8
Select two options which are security Issues which need to be modified before RouterA is used? (Choose two.)
A. unencrypted weak password is configured to protect privilege mode
B. inappropriate wording in banner message
C. the virtual terminal lines have a weak password configured
D. virtual terminal lines have a password, but it will not be used
E. configuration supports un-secure web server access
Correct Answer: BD
QUESTION 9
Select three options which are security issues with the current configuration of SwitchA. (Choose three.)
A. privilege mode is protected with an unencrypted password
B. inappropriate wording in banner message
C. virtual terminal lines are protected only by a password requirement
D. both the username and password are weak
E. telnet connections can be used to remotely manage the switch
F. cisco user will be granted privilege level 15 by default
Correct Answer: ABD
QUESTION 10
Which two of the following are true regarding the configuration of RouterA? (Choose two.)
A. at least 5 simultaneous remote connections are possible
B. only telnet protocol connections to RouterA are supported
C. remote connections to RouterA using telnet will succeed
D. console line connections will nevertime out due to inactivity
E. since DHCP is not used on Fa0/1 there is not a need to use the NAT protocol
Correct Answer: AC
QUESTION 11
Which of the following is true regarding the configuration of SwitchA?
A. only 5 simultaneous remote connections are possible
B. remote connections using ssh will require a username and password
C. only connections from the local network will be possible
D. console access to SwitchA requires a password
Correct Answer: B QUESTION 12
What is the subnet broadcast address of the LAN connected to Router1?
A. 192.168.8.15
B. 192.168.8.31
C. 192.168.8.63
D. 192.168.8.127
Correct Answer: A QUESTION 13
What is the bandwidth on the WAN interface of Router 1?
A. 16 Kbit/sec
B. 32 Kbit/sec
C. 64 Kbit/sec
D. 128 Kbit/sec
E. 512 Kbit/sec
F. 1544 Kbit/sec
Correct Answer: A
QUESTION 14
Including the address on the Routed Ethernet interface, how many hosts can have IP addresses on the LAN to which Routed is connected?
A. 6
B. 30
C. 62
D. 126
Correct Answer: A QUESTION 15
The hosts in the LAN are not able to connect to the Internet. Which commands will correct this issue?
A. Router1(conf)#interface fa0/0 Router1(conf-if)#no shutdown
B. Router1(conf)#interface fa0/1 Router1(conf-if)#no shutdown
C. Router1(conf)#interface s0/0 Router1(conf-if)#no shutdown
D. Router1(conf)#interface s0/1 Router1(conf-if)#no shutdown
E. Router1(conf)#interface s0/0 Router1(conf-if)#ip address 10.11.12.13 255.255.255.252
F. Router1(conf)#interface s0/1 Router1(conf-if)#ip address 10.100.1.1 255.255.255.252
Correct Answer: B
Flydumps Cisco 100-101 Questions and Answers Products basically comprise of the simulated Cisco 100-101 exam questions AND their most correct answers, accompanied with a methodical elucidation of the Cisco 100-101 answers and the probable wrong answers.The extent to which Cisco 100-101 Questions and Answers Products cover their Cisco subject is so thorough, that once you are done with a Cisco product, passing the Cisco 100-101 exam in first attempt should be a piece of cake.
Pass4itsure 1z1-060 dumps with PDF + Premium VCE + VCE Simulator: http://www.pass4itsure.com/1z1-060.html
The post Cisco 100-101 Exam Sample, 100% Pass Cisco 100-101 Exam Collection For Sale appeared first on IT Certification Success Guaranteed, The Easy Way!.